How To Use Carburize In A Sentence
-
-- The carbon - and nickel-steel gears are carburized separately owing to the difference in time necessary for their carburization.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
The rivet stud shown in Fig. 37 is carburized while of its full diameter and then turned down to the size of the rivet end, thus cutting away the carburized surface.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
Tough steels with a carbon content of less than 0.25% can be enriched with carbon (carburized) on their surfaces so that they contain 0.75 to
7. Surface Hardening
-
The degree to which a bar may be decarburized depends upon the chemical analysis of the steel.
-
In fact it is very difficult to distinguish between these two hardening agents when examining a carburized steel under the microscope.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
Steel containing from 3 to 3.5 per cent of nickel is carburized between 1,650 and
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
This process unfortunately requires for its prompt success the use of a very large quantity of spiegel or of ferro-manganese, in order to sufficiently carburize and deoxidize the burnt iron, which is the final product of the blowing.
Scientific American Supplement, No. 315, January 14, 1882
-
carburize metal
-
The carburized sleeves are heated in an automatic furnace, which takes them cold at the back and feeds them through to the front, by which time they are at the correct temperature.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
In the original cooling or through subsequent heat treatment, a matrix can be internally decarbonized or carburized by depositing graphite on existing sites or by dissolving carbon from them.
-
His pressure tests burst the steel pipes in a week, revealing that the dense hydrogen had decarburized inner layers to a hard and brittle stuff.
-
A good mixture should be porous, so that the evolved gases, which should be generated at the proper temperature, may move freely around the steel objects being carburized; should be a good conductor of heat; should possess minimum shrinkage when used; and should be capable of being tamped down.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
Mixed with raw bone it will carburize more rapidly, and still more so if mixed with burnt bone.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
The most satisfactory steel to carburize contains between 0.10 and 0.20 per cent carbon, less than 0.35 per cent manganese, less than 0.04 per cent phosphorus and sulphur, and low silicon.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
decarburized surface" decarburized edge zone to be removed or recarburized by inserting - normalizing
4. Annealing
-
A two step process is then required; the first producing the carburized bloom and the second, a heat-treatment to decarburize the iron for proper forging.
-
The advantages in the hardening start with the carburizing operation, as a steel of uniform and fine grain size will carburize more uniformly, producing
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
That is, the hardenability of the case is significantly greater when nitrogen is added by carbonitriding than when the same steel is only carburized.
-
In this paper, according to the test results, the functional relationship between the surface hardness value (HV)and the load for nitrided and nitrocarburized layer was studied by regression analysis.
-
Practically all printed information on the subject is to the effect that nickel steel takes longer to carburize than plain carbon steel.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
So long before being forwarded to Tampa Town, the iron ore, molten in the great furnaces of Coldspring, and brought into contact with coal and silicium heated to a high temperature, was carburized and transformed into cast iron.
From the Earth to the Moon
-
This long heat treatment increases cost, limits rate of production and decarburizes the surface layer.
-
In the original cooling or through subsequent heat treatment, a matrix can be internally decarbonized or carburized by depositing graphite on existing sites or by dissolving carbon from them.
-
On Earth, that†™ s a super-hard ceramic use to grind carburized steel.
365 tomorrows » 2007 » February : A New Free Flash Fiction SciFi Story Every Day
-
So long before being forwarded to Tampa Town, the iron ore, molten in the great furnaces of Coldspring, and brought into contact with coal and silicium heated to a high temperature, was carburized and transformed into cast iron.
From the Earth to the Moon
-
It was found that its oxygen index, smoke density were directly proportional to content of carburizer whereas its initial expanding time was inversely proportional to content of carburizer.
-
The carburization then goes on for several hours before the furnace is cooled below the effective carburizing range, securing an ideal diffusion of carbon between the case and the core of the steel being carburized.
The Working of Steel Annealing, Heat Treating and Hardening of Carbon and Alloy Steel
-
Manganese ores are used mainly in the manufacture of steel, the alloys spiegeleisen and ferromanganese being added to the molten steel after treatment in the Bessemer converter and open-hearth furnace in order to recarburize and purify the metal.
The Economic Aspect of Geology
-
This process unfortunately requires for its prompt success the use of a very large quantity of spiegel or of ferro-manganese, in order to sufficiently carburize and deoxidize the burnt iron, which is the final product of the blowing.
Scientific American Supplement, No. 315, January 14, 1882
-
The results have given a theoretical basis on the favorable design of carburizing parameters, for the accurate control of depth and carbon distribution in carburized layer.
-
This product deoxidizes, descales, and decarburizes steel, copper alloys, iron, and other noble alloys.
